Pemanfaatan Limbah Plastik Polyethylene Terephthalate (PET) dan Batok Kelapa Sebagai Bahan Baku Paving Block
DOI:
https://doi.org/10.23960/jabe.v2i2.7480
Abstract View: 627
Abstract
In 2021 the total amount of waste from various types of waste in Indonesia alone will reach 68,5 milion tons. Based on these data, as much as 17 percent, or around 11,6 milion tons, was contributed by jenna R.Jambeck from the University of Geogia in 2010, there were 275 tons of plastic waste produced worlwide. Around 4,8-12,7 milion tons of them are waste and pollute the sea. Indonesia itself has a coastal population of 187,2 ,milion which annually produces plastic waste. Around 0,48-1,29 milion tonnes of plastic waste is thought to have polluted the oceans. To overcome this, proper management of plastic waste is needed, one of which is by making paving blocks made from plastic waste. The study aims to determine the characteristics of thr various composition paving blocks according to the Dquality standard, which is used for garden pavements and other uses. In this study, aratio of 1:1:1 was used for plastic, sand, and oil. Then coconut shells were added to the treatment P1 as much as 3%, P2 as much as 6%, P3 as much as 9%, and P4 as much as 12% of the paving block volume paving block quality standardD has requirements, namely the maximum value obtained from the results of the compressive strength test is 10 Mpa and water absorption is 10%. From the result of the research that i did, it was found that the variations in the P treatment were closestto the quality standard D, with a compressive strength test value of 5,84 Mpa.
Keywords : Coconut Shells, Paving Blocks, PET, Plastic, Waste.
Downloads
References
Agnes Yuanita Bintoro, Arthur Daniel Limantara, S. W. (2018). Halus Dan Agregat Kasar Dari Tempurung Kelapa. Jurmateks, 1(1), 160–171.
Ruben Simatupang. (2016). Studi Eksperimen Analisa Koefisien Gesek Pada Saat Terjadi Fenomena Stick-Slip Friction Pada Reciprocating Contact Pada Saat Terjadi Fenomena Stick-Slip. In Intitut Teknologi Sepuluh November.
Sijabat, F. I., & Saragih, J. (2013). Komposit Poliester Tak Jenuh Terhadap Sifat Mekanik. 2(4), 31–37.
Suhartana. (2006). Baku Arang Aktif Dan Aplikasinya Untuk Penjernihan Air Sumur Di Desa Belor. Pemanfaatan Tempurung Kelapa. 9(3), 151–156.
Syukur Sebayang I Wayan Diana, A. P. (2011). Perbandingan Mutu Paving Block Produksi Manual Dengan Produksi Masinal. Jurnal Rekayasa, 15(2), 139–150.
Wahyudi, J., Prayitno, H. T., Astuti, A. D., Perencanaan, B., Daerah, P., & Pati, K. (2018). Pemanfaatan Limbah Plastik Sebagai Bahan Baku Pembuatan Bahan Bakar Alternatif The Utilization Of Plastic Waste As Raw Material For. XIV(1), 58–67
Downloads
Published
How to Cite
Issue
Section
License
Authors who publish with this journal agree to the following terms:
Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution-ShareAlike 4.0 International Lice that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.
Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access).
Jurnal Agricultural Biosystem Engineering
JABE is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
