Improving efficiency in green tea production time using lean manufacturing approach with value stream mapping: A case study at PT Candi Loka [Perbaikan efisiensi waktu produksi teh hijau menggunakan pendekatan produksi ramping dengan value stream mapping: Studi kasus di PT Candi Loka]
DOI:
https://doi.org/10.23960/jtihp.v29i2.132-143
Abstract View: 807
Keywords:
green tea, lean manufacturing, time efficiency, value stream mappingAbstract
Green tea production activities at PT Candi Loka indicated a time-consuming, which caused process efficiency to be less than optimal. Process efficiency improvements must be made to increase company competitiveness and consumer satisfaction. This research aimed to analyze the efficiency of green tea production time at PT Candi Loka by identifying the processing time required in each production activity, including the time consumption and formulating recommendations for improvement using a lean manufacturing approach using the VSM (Value Stream Mapping) method. There were 30 activities in 6 processes consisting of receiving raw materials, withering, rolling, drying, and packaging. Identification of value streams using the PAM (Process Activity Mapping) tool produced 9 Value added (VA) activities, 19 Necessary but Non-Value Added (NNVA) activities, and 2 Non-Value Added (NVA) activities in the form of delays in the withering and drying processes. In the current state map analysis, the production lead time value was 315.286 seconds. Recommended improvements to eliminate delays in the withering process were to set up the rotary panner machine earlier and increase the number of supervisors, while to eliminate delays in the drying process were to implement a piece rate system. Increasing efficiency was also carried out by improving NNVA activities by adding weighbridge facilities and using a conveyor system. The future state map proposed by implementing recommended improvements resulted in an increase in production time efficiency to 222.356 seconds and an increase in the process cycle efficiency value from 58.95% to 84.85%.
Downloads
References
Anggraini, W., Kusumanto, I., Permata, E. G., & Yola, M. (2020). Pendekatan lean services untuk perbaikan pelayanan administrasi akademik perguruan tinggi. Jurnal Teknik Industri: Jurnal Hasil Penelitian dan Karya Ilmiah dalam Bidang Teknik Industri, 6(1), 21. https://doi.org/10.24014/jti.v6i1.5246
Chimezie, O.S., Isaac,O.E, & Nkoi, B. (2023). Determination of boiler maintenance effectiveness on productivity in a palm oil producing company: A case study. International Journal of Engineering and Modern Technology (IJEMT), 8(1). https://doi: 10.56201/ijemt.v9.no1.2023.pg33.41
Delbridge, R., & Lowe, J. (1997). Manufacturing control: supervisory systems on the `new’ shop floor. Sociology, 31(3), 409–426. https://doi.org/10.1177/0038038597031003003
Dhika, D. A., Witonohadi, A., & Akbari, A. D. (2023). The proposed warehouse improvement using lean approach to eliminate waste at the main warehouse of PT. XYZ. Opsi, 16(1), 94. https://doi.org/10.31315/opsi.v16i1.7310
Fadhilah, Z. H., Perdana, F., & Syamsudin, R. A. M. R. (2021). Review: telaah kandungan senyawa katekin dan epigalokatekin galat (EGCG) sebagai antioksidan pada berbagai jenis teh. Jurnal Pharmascience, 8(1), 31–44. https://doi.org/10.20527/jps.v8i1.9122
Fajar, R. I., Wrasiati, L. P., & Suhendra, L. (2018). Kandungan senyawa flavonoid dan aktivitas antioksidan ekstrak teh hijau pada perlakuan suhu awal dan lama penyeduhan. Jurnal Rekayasa dan Manajemen Agroindustri, 6(3), 196. https://doi.org/10.24843/jrma.2018.v06.i03.p02
Fauziah, Y., Wijaya, E. O., Setiawan, I., & Nugroho, B. H. (2022). Improving the efficiency of material transfer system using Value Stream Mapping (VSM): A case study in the shoe industry. Journal Industrial Servicess, 8(2), 181–186. https://doi.org/10.36055/jiss.v8i2.15908
Foyer, G., & Schulz, K. (2021). Overview study of the use of several weighing instruments for static determination of vehicle mass in Germany. Measurement: Sensors, 18, 100114. https://doi.org/10.1016/j.measen.2021.100114
Gebeyehu, S. G., Abebe, M., & Gochel, A. (2022). Production lead time improvement through lean manufacturing. Cogent Engineering, 9(1). https://doi.org/10.1080/23311916.2022.2034255
Groneberg, H., Horstkotte, R., Pruemmer, M., Bergs, T., & Döpper, F. (2022). Concept for the reduction of non-value-adding operations in Laser Powder Bed Fusion (L-PBF). Procedia CIRP, 107, 344–349. https://doi.org/10.1016/j.procir.2022.04.056
Guiteras, R. P., & Jack, B. K. (2018). Productivity in piece-rate labor markets: Evidence from rural Malawi. Journal of Development Economics, 131, 42–61. https://doi.org/10.1016/j.jdeveco.2017.11.002
Habib, M. A., Rizvan, R., & Ahmed, S. (2023). Implementing lean manufacturing for improvement of operational performance in a labeling and packaging plant: A case study in Bangladesh. Results in Engineering, 17, 100818. https://doi.org/10.1016/j.rineng.2022.100818
Hanafie, A., Darty Akhsa, A. C., Alam, N., & Sandy, A. (2020). Rancang bangun sistem konveyor penghitung telur otomatis. ILTEK : Jurnal Teknologi, 15(01), 1–4. https://doi.org/10.47398/iltek.v15i01.1
Karabay, G., & Kansul, D. S. (2019). Increasing the process cycle efficiency of a men trousers assembly line. Tekstil ve Konfeksiyon, 29(3), 253–261. https://doi.org/10.32710/tekstilvekonfeksiyon.498921
Khoeruddin, R., & Indrasti, D. (2023). Analisis lean manufacturing produksi saus gulai dengan metode Value Stream Mapping. Jurnal Mutu Pangan : Indonesian Journal of Food Quality, 10(1), 15–23. https://doi.org/10.29244/jmpi.2023.10.1.15
Lestari, P. W., Harianto, S., Prawira-Atmaja, M. I., Andriyani, M., Shabri, S., Maulana, H., & Putri, S. H. (2022). Identifikasi sifat fisik produk samping dari mesin ball tea pada pengolahan teh hijau. Jurnal Teknotan, 16(2), 85. https://doi.org/10.24198/jt.vol16n2.4
Liu, Q., & Yang, H. (2017). Lean implementation through value stream mapping: A case study of a footwear manufacturer. 2017 29th Chinese Control And Decision Conference (CCDC), 3390–3395. https://doi.org/10.1109/CCDC.2017.7979092
Marques, J. P., Sá, J. C., Silva, F. J. G., Pereira, T., Ferreira, L. P., & Santos, G. (2021). Safety efficiency value stream mapping (SEVSM) - A new tool to support the implementation of Lean Safety. IOP Conference Series: Materials Science and Engineering, 1193(1), 012124. https://doi.org/10.1088/1757-899X/1193/1/012124
Ma’sum, A., & Setiafindari, W. (2022). Analisis pemborosan pada proses produksi dengan Metode Value Stream Mapping di PT Mandiri Jogja Internasional. Jurnal Cakrawala Ilmiah, 1(10), 2517–2526. https://doi.org/10.53625/jcijurnalcakrawalailmiah.v1i10.2582
Mendes, D. S. F. T., Navas, H. V. G., & Charrua-Santos, F. M. B. (2023). Improving the performance of a conveyor belt through lean philosophy and Industry 4.0. Journal of Quality in Maintenance Engineering, 29(4), 842–862. https://doi.org/10.1108/JQME-09-2022-0055
Misbah, A., Pratikto, P., & Widhiyanuriyawan, D. (2015). Upaya meminimalkan non value added activities produk mebel dengan penerapan metode lean manufacturing. Journal of Engineering and Management Industrial System, 3(1). https://doi.org/10.21776/ub.jemis.2015.003.01.8
Novitasari, R., & Iftadi, I. (2020). Analisis lean manufacturing untuk minimasi waste pada proses door PU. Jurnal INTECH Teknik Industri Universitas Serang Raya, 6(1), 65–74. https://doi.org/10.30656/intech.v6i1.2045
Nucci, F. (2017). Machines set up the reduction in lean manufacturing environment. DEStech Transactions on Engineering and Technology Research. https://doi.org/10.12783/dtetr/icamm2016/7406
Nugraha, G. D. Y., Prayogo, R. C., Syafitri, A. K. N., Berlian, I. N., Pratama, R. J. A., & Widianto, E. D. (2017). Sistem identifikasi beban angkutan barang yang terintegrasi pada jembatan timbang menggunakan kartu RFID. Jurnal Fakultas Teknik, 18(2). https://doi.org/10.30595/techno.v18i2.1958
Omogbai, O., & Salonitis, K. (2016). Manufacturing system lean improvement design using discrete event simulation. Procedia CIRP, 57, 195–200. https://doi.org/10.1016/j.procir.2016.11.034
Poswa, F., Adenuga, O. T., & Mpofu, K. (2022). Productivity improvement using simulated value stream mapping: A case study of the truck manufacturing industry. Processes, 10(9), 1884. https://doi.org/10.3390/pr10091884
Prayudo, A. N., Fathorrahman, F., & Karnawati, T. A. (2020). Analisis Pengaruh masa kerja, upah dan usia terhadap produktivitas tenaga kerja buruh borongan linting rokok di SKT Gebog, PT. Djarum Kudus. Jurnal Ekonomi Manajemen dan Bisnis, 1(1), 1–10. https://doi.org/10.32815/jubis.v1i1.311
Ratnani, S., & Malik, S. (2022). Therapeutic properties of green tea: A review. Journal of Multidisciplinary Applied Natural Science, 2(2), 90–102. https://doi.org/10.47352/jmans.2774-3047.117
Salwin, M., Jacyna-Gołda, I., Bańka, M., Varanchuk, D., & Gavina, A. (2021). Using Value Stream Mapping to eliminate waste: A case study of a steel pipe manufacturer. Energies, 14(12), 3527. https://doi.org/10.3390/en14123527
Satria, T., & Yuliawati, E. (2018). Perancangan lean manufacturing dengan menggunakan Waste Assessment Model (WAM) dan VALSAT untuk meminimumkan waste (Studi Kasus: PT. XYZ). Jurnal Rekayasa Sistem Industri, 7(1), 55. https://doi.org/10.26593/jrsi.v7i1.2828.55-63
Shou, W., Wang, J., Wu, P., & Wang, X. (2020). Value adding and non-value adding activities in turnaround maintenance process: classification, validation, and benefits. Production Planning & Control, 31(1), 60–77. https://doi.org/10.1080/09537287.2019.1629038
Srihastuti, E., Agustin, B. H., & Suntoro, R. C. (2023). Analisis perhitungan pajak penghasilan orang pribadi atas wajib pajak penerima upah harian dan upah borongan sesuai dengan ketentuan Undang – Undang Harmonisasi Peraturan Perpajakan (HPP). JURA : Jurnal Riset Akutansi, 1(4), 80–87. https://doi.org/10.54066/jura-itb.v1i4.840
Ulfah, M., Trenggonowati, D. L., Lean, P., & Sigma, S. I. X. (2023). Minimizing seven wastes in the inner lid production process using the lean six sigma approach. Jurnal Teknologi Industri Pertanian, 33(2), 117–129. https://doi.org/10.24961/j.tek.ind.pert.2023.33.2.117
Wurjaningrum, F., Shafak, C.A., 2022. How does the value stream mapping method identify waste and improve the coffee bean production process of a café?. Journal Of Theoretical And Applied Management, 15 (3),362 – 375 https://doi.org/10.20473/jmtt.v15i3.40440
Yang, M. M., Yang, F., Cui, T., & Cheng, Y.-C. (2019). Analysing the dynamics of mental models using causal loop diagrams. Australian Journal of Management, 44(3), 495–512. https://doi.org/10.1177/0312896218823831
Zhang, X., Zhu, X., & Wang, R. (2024). Simulation and identification of multiscale falling morphology of fresh tea leaves at different transport speeds based on discrete element method. HortScience, 59(2), 167–172. https://doi.org/10.21273/HORTSCI17548-23
Downloads
Published
How to Cite
Issue
Section
License
Authors who publish with this journal agree to the following terms:
- Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
- Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.
- Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work
Jurnal Teknologi & Industri Hasil Pertanian is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
.png)
